Question

2

How do I fix a garbled screen on a Gateway LT3103u?

rated 0 times [ 2] [ 0] / answers: 1 / hits: 2053 / 2 Years ago, sat, june 11, 2022, 12:31:59

I've been having garbled screen problems on a Gateway LT3103u on Ubuntu for a while. I just did a fresh install of Ubuntu 11.10 and continue to have issues. I installed xubuntu-desktop in case the issues had to do with the sophisticated GNOME graphics. The problem is less bad, but it's still there. After a few minutes of using XFCE, the screen gets garbled. I assume this has something to do with the graphics card, but I don't know how to go about troubleshooting something like this. Where should I start? garbled screen

Update: Here is the description of the VGA card from lspci -vvv:

01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] (prog-if 00 [VGA controller])

Subsystem: Acer Incorporated [ALI] Device 028c

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 64, Cache Line Size: 32 bytes

Interrupt: pin A routed to IRQ 18

Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]

Region 2: Memory at f0100000 (64-bit, non-prefetchable) [size=64K]

Region 4: I/O ports at 9000 [size=256]

Region 5: Memory at f0000000 (32-bit, non-prefetchable) [size=1M]

Expansion ROM at <unassigned> [disabled]

Capabilities: [50] Power Management version 2

Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)

Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit+

Address: 0000000000000000  Data: 0000

Kernel driver in use: radeon

Kernel modules: radeon

Update: Setting GRUB_CMDLINE_LINUX="nomodeset" in /etc/default/grub seems to have fixed it in both Ubuntu and xubuntu-desktop. I will test it for a day or so to see if the problems recur and then post more detail with some links to an explanation.

Answers

Only authorized users can answer the question. Please sign in first, or register a free account.

tocklftime

Add To Favorites

Follow

Total Points: 110

Total Questions: 109

Total Answers: 100

Location: Mayotte

Member since Mon, Sep 12, 2022

2 Years ago

answered 2 Years ago epypian · Accepted Answer

It turns out this post is the answer I was looking for. The trouble is something called kernel mode-setting (KMS), which according to the Ubuntu wiki

shifts responsibility for selecting and setting up the graphics mode from X.org to the kernel. When X.org is started, it then detects and uses the mode without any further mode changes.

However, Radeon graphics cards are unevenly supported by the kernel, and KMS is turned on automatically in newer versions of Ubuntu, despite it not working with older cards. This is probably the reason why upgrading Ubuntu caused these problems.

To remove KMS in GRUB 2, add nomodeset to GRUB_CMD_LINUX (GRUB_CMD_LINUX="nomodeset") in /etc/default/grub and run sudo update-grub. Reboot.